COMPLETE UNI-INDUSTRIAL CHIMNEY 12MB FI160 DINOFLAME
Brand: DINOFLAME
Product Code: as_DF_UNI_12_160_1064
Availability: In Stock
€1,179.88 Ex Tax: €959.25

KOMIN UNI DINOFLAME WITH A FI 160 DIAMETER AND 12MB HEIGHT.

UNIVERSAL- Works with boilers for solid fuels such as: coal, coke, wood, eco-pea, fine coal, as well as with wet fuels such as: gas or fuel oil. The chimney has the best A1N1 contributions in accordance with EN 1457 A1

ISOLATED- The set includes mineral wool boards, made of glass fibers, with increased resistance to high temperatures. The boards are on one side covered with a white, reinforced glass veil allowing easier assembly.

COMPLETE- The chimney kit ordered has all the necessary elements to put the chimney.

STAINLESS STEEL- Resistant to acids contained in combustion gases, including sulfur compounds, resulting from the combustion of hard coal and fine coal (acid resistance. 2%).

RESISTANT- for soot and high temperature fire, which is necessary for boilers for solid fuels C. O. and fireplaces. (temp. 600 C)


CONCRETE SLABS(under the brickwork and covering are additional elements not attached to the chimney set. Available in related elements or chimney elements).

FIRST STARTING THE CHIMNEY- After 7 days from the end of assembly.

CONNECTION OF THE BOILER- By connecting pipes. A connecting element with a wrapped cord should be used to protect the ceramic T-pipe from damage caused by steel expansion (available in accessories).

TRANSMISSIONS THROUGH STROPS- They should be dilated with hard wool (minimum 3 cm), in order to avoid pressure of the board on the keramzite chimney casing, which causes its damage. In the case of openings in the ceilings, holes should be prepared in dimensions of 3 cm larger than the outer dimensions of the expanded clay block.

MORTAR PROPORTIONS- The mortar should be prepared in 1/7 proportions, i.e. one measure of water and seven measures of mortar. Cure time is 24h at 20 C, curing takes place after about 10 days. The mixture is not suitable for processing at temperatures below 5 ° C. To reduce the drying time, use water at 40-50 C. After reconstitution, the mortar has the consistency of a crumbly mass, which within 5 minutes takes on the consistency of a smooth putty and only then is it ready to be used.

BRICKLAYING- When building blocks, it is necessary to apply masonry mortar (cement, cement-lime), so that excessive amounts of it do not enter the chimney and do not stiffen its ceramics, which may lead to its cracking.

OVER THE ROOF- The chimney should be covered with hard insulation wool, which is non-flammable. Styrofoam, as a flammable material, should not be used at the chimney casing.

COMPLETING THE CHIMNEY- The chimney should be terminated with a special cone mounted approx. 2 - 4 cm above the formwork to cover the chimney and allow the ceramic to work along its entire length. The roof with the formwork prevents water from entering the chimney insulation.

SECURITY DURING MELTING- When finishing a certain stage of the chimney on a given day, the chimney should be protected against weather conditions. Falling rain can irreparably damage thermal insulation.

Technical parameters of the DinoFlame UNI system:

The UNI DinoFlame kit includes:

L. p.

name of the element

quantity

1.

chimney block

36

2.

canopy cone

1

3.

cleanout door

1

4.

chimney insulation

36

5.

KIT 1.5 kg mortar

2

6.

face plate - wool

1

7.

chimney pipe flue

1

8.

chimney pipe

33

9.

chimney pipewashout

1

10.

condensate tank

1

11.

plug for cleaning

1

12.

cutter knife

1

13.mounting pins4
14.tube squeezer1
15.lost timber1
16.ventilation grille
1
17.front panel hook4



Available options:

  • Additional 0.33m module consisting of:
    - 1x keramzyt block
    - 1x ceramic straight pipe
    - 1x insulation set
  • Additional 0.66m module consisting of:
    - 2x clay aerosol block
    - 2x ceramic straight pipe
    - 2x insulation set
  • An additional cleaning form that includes:
    - 1x 658mm cleanout fitting
    - 1x galvanized steel door
    - 1x cleanout plug
  • Additional shape with a cloak which includes:
    - 1x fittings for a 658mm long fuse
    - 1x mineral wool front panel
    - 4x front panel hook

ADDITIONAL CARD OR CHANNEL MODULE (AFTER CHOOSING THE RIGHT VARIANT) IS ADDED IN REPLACEMENT FOR THE COMPLEMENTARY MODULE OR THE TOTAL HEIGHT OF THE CHIMNEY IS NOT SUBJECT CHANGING. AND THE COST OF AN ADDITIONAL MODULE IS A DIFFERENCE BETWEEN THEM AND A SUPPLEMENTARY MODULE.
IF THE CHIMNEY IS TO BE INCREASED BY 0.33M OR BY 0.66M, PLEASE CHOOSE THE RIGHT VARIANT ABOVE.



Characteristics of elementssystemDinoFlame UNI
CERAMIC CHIMNEY INSERTS

KERAMISTE - CONCRETE PAINTINGS

A COMPLETE SET OF ELEMENTS AT THE UNI DINOFLAME KIT


Technical data
stuffceramics / expanded clay
ManufacturerDinoFlame
System modelUni
Type of insulationinsulated
Type of blockOne channel
External dimension350x350 mm
Fuel typeSolid fuels
Height12.00 m
Guarantee period. Guarantee period30 years
Diameter of the chimneyFI 160
Weight1064 kg
Proportion of KIT NISOTT 2010 mortarWarrantyLeaflet of the UNI DinoFlame chimneyDeclaration of conformity UNI DinoFlame


Product available on request. Delivery costs set individually, please email, use contact form or call us to determine the cost of delivery.

Write a review

Please login or register to review